Cisco 640-802 덤프자료

Cisco인증 640-802시험은 IT인증자격증중 가장 인기있는 자격증을 취득하는 필수시험 과목입니다. Cisco인증 640-802시험을 패스해야만 자격증 취득이 가능합니다. ITExamDump의Cisco인증 640-802는 최신 시험문제 커버율이 높아 시험패스가 아주 간단합니다. Cisco인증 640-802덤프만 공부하시면 아무런 우려없이 시험 보셔도 됩니다. 시험합격하면 좋은 소식 전해주세요.

많은 시간과 돈이 필요 없습니다. 30분이란 특별학습가이드로 여러분은Cisco 640-802인증시험을 한번에 통과할 수 있습니다, ITExamDump에서Cisco 640-802시험자료의 문제와 답이 실제시험의 문제와 답과 아주 비슷한 덤프만 제공합니다.

시험 번호/코드: 640-802

시험 이름: Cisco (Cisco Certified Network Associate(CCNA))

우리ITExamDump 에서 제공하는 학습가이드에는 IT전문가들이 만들어낸 시험대비 자료들과Cisco 640-802인증시험의 완벽한 문제와 답들입니다. 그리고 우리ITExamDump에서는 IT업계에서의 높은 신뢰감으로 여러분들한테 100%보장을 드립니다. 우리에 믿음을 드리기 위하여Cisco 640-802관련자료의 일부분 문제와 답 등 샘플을 무료로 다운받아 체험해볼수 있게 제공합니다.

ITExamDump이 바로 아주 좋은Cisco 640-802인증시험덤프를 제공할 수 있는 사이트입니다. ITExamDump 의 덤프자료는 IT관련지식이 없는 혹은 적은 분들이 고난의도인Cisco 640-802인증시험을 패스할 수 있습니다. 만약ITExamDump에서 제공하는Cisco 640-802인증시험덤프를 장바구니에 넣는다면 여러분은 많은 시간과 정신력을 절약하실 수 있습니다. 우리ITExamDump 의Cisco 640-802인증시험덤프는 ITExamDump전문적으로Cisco 640-802인증시험대비로 만들어진 최고의 자료입니다.

640-802 덤프무료샘플다운로드하기: http://www.itexamdump.com/640-802.html

NO.1 Your ISP has given you the address 223.5.14.6/29 to assign to your router's interface. They have also
given you the default gateway address of 223.5.14.7. After you have configured the address, the router is
unable to ping any remote devices. What is preventing the router from pinging remote devices?
A. The default gateway is not an address on this subnet.
B. The default gateway is the broadcast address for this subnet.
C. The IP address is the broadcast address for this subnet.
D. The IP address is an invalid class D multicast address.
Answer: B

Cisco   640-802   640-802덤프   640-802   640-802

NO.2 Which command is used to configure a default route?
A. ip route 172.16.1.0 255.255.255.0 0.0.0.0
B. ip route 172.16.1.0 255.255.255.0 172.16.2.1
C. ip route 0.0.0.0 255.255.255.0 172.16.2.1
D. ip route 0.0.0.0 0.0.0.0 172.16.2.1
Answer: D

Cisco   640-802 dump   640-802기출문제   640-802

NO.3 If IP routing is enabled, which two commands set the gateway of last resort to the default gateway?
(Choose two.)
A. ip default-gateway 0.0.0.0
B. ip route 172.16.2.1 0.0.0.0 0.0.0.0
C. ip default-network 0.0.0.0
D. ip default-route 0.0.0.0 0.0.0.0 172.16.2.1
E. ip route 0.0.0.0 0.0.0.0 172.16.2.1
Answer: CE

Cisco   640-802 dumps   640-802   640-802

NO.4 Which command shows system hardware and software version information?
A. show configuration
B. show environment
C. show inventory
D. show platform
E. show version
Answer: E

Cisco   640-802시험문제   640-802최신덤프   640-802   640-802

NO.5 Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.
1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2
the native VLAN is not specified.What will happen in this scenario?
A. 802.1Q giants frames could saturate the link.
B. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.
C. A native VLAN mismatch error message will appear.
D. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.
Answer: C

Cisco   640-802기출문제   640-802자격증

NO.6 Which command is used to copy the configuration from RAM into NVRAM?
A. copy running-config startup-config
B. copy startup-config: running-config:
C. copy running config startup config
D. copy startup config running config
E. write terminal
Answer: A

Cisco   640-802덤프   640-802   640-802

NO.7 When troubleshooting a Frame Relay connection, what is the first step when performing a loopback
test?
A. Set the encapsulation of the interface to HDLC.
B. Place the CSU/DSU in local-loop mode.
C. Enable local-loop mode on the DCE Frame Relay router.
D. Verify that the encapsulation is set to Frame Relay.
Answer: A

Cisco pdf   640-802인증   640-802   640-802시험문제   640-802

NO.8 Which command would you configure globally on a Cisco router that would allow you to view directly
connected Cisco devices?
A. enable cdp
B. cdp enable
C. cdp run
D. run cdp
Answer: C

Cisco   640-802덤프   640-802   640-802인증

NO.9 Which layer in the OSI reference model is responsible for determining the availability of the receiving
program and checking to see if enough resources exist for that communication?
A. transport
B. network
C. presentation
D. session
E. application
Answer: E

Cisco최신덤프   640-802   640-802   640-802기출문제   640-802기출문제

NO.10 Which command is used to see the path taken by packets across an IP network?
A. show ip route
B. show route
C. traceroute
D. trace ip route
Answer: C

Cisco   640-802   640-802 dumps   640-802

NO.11 A network administrator must configure 200 switch ports to accept traffic from only the currently
attached host devices. What would be the most efficient way to configure MAC-level security on all these
ports?
A. Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security
mac-address command.
B. Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security
mac-address command.
C. Use the switchport port-security MAC address sticky command on all the switch ports that have end
devices connected to them.
D. Use show mac-address-table to determine the addresses that are associated with each port and then
enter the commands on each switch for MAC address port-security.
Answer: C

Cisco   640-802   640-802

NO.12 What must be set correctly when configuring a serial interface so that higher-level protocols calculate
the
best route?
A. bandwidth
B. delay
C. load
D. reliability
Answer: A

Cisco dumps   640-802기출문제   640-802

NO.13 A company implements video conferencing over IP on their Ethernet LAN. The users notice that the
network slows down, and the video either stutters or fails completely. What is the most likely reason for
this?
A. minimum cell rate (MCR)
B. quality of service (QoS)
C. modulation
D. packet switching exchange (PSE)
E. reliable transport protocol (RTP)
Answer: B

Cisco dumps   640-802   640-802 pdf

NO.14 Workstation A has been assigned an IP address of 192.0.2.24/28. Workstation B has been assigned an
IP address of 192.0.2.100/28. The two workstations are connected with a straight-through cable. Attempts
to ping between the hosts are unsuccessful. What two things can be done to allow communications
between the hosts? (Choose two.)
A. Replace the straight-through cable with a crossover cable.
B. Change the subnet mask of the hosts to /25.
C. Change the subnet mask of the hosts to /26.
D. Change the address of Workstation A to 192.0.2.15.
E. Change the address of Workstation B to 192.0.2.111.
Answer: AB

Cisco인증   640-802자격증   640-802   640-802   640-802기출문제   640-802 dumps

NO.15 When you are logged into a switch, which prompt indicates that you are in privileged mode?
A. %
B. @
C. >
D. $
E. #
Answer: E

Cisco   640-802시험문제   640-802   640-802   640-802자료

NO.16 When configuring a serial interface on a router, what is the default encapsulation?
A. atm-dxi
B. frame-relay
C. hdlc
D. lapb
E. ppp
Answer: C

Cisco   640-802   640-802 pdf   640-802   640-802 dump

NO.17 Which protocols are found in the network layer of the OSI reference model and are responsible for
path determination and traffic switching?
A. LAN
B. routing
C. WAN
D. network
Answer: B

Cisco   640-802   640-802   640-802

NO.18 Which two addresses can be assigned to a host with a subnet mask of 255.255.254.0? (Choose two.)
A. 113.10.4.0
B. 186.54.3.0
C. 175.33.3.255
D. 26.35.2.255
E. 17.35.36.0
Answer: BD

Cisco자료   640-802자격증   640-802   640-802 pdf   640-802

NO.19 Which command is used to debug a ping command?
A. debug icmp
B. debug ip icmp
C. debug tcp
D. debug packet
Answer: B

Cisco dumps   640-802   640-802   640-802자료

NO.20 Which command would correctly configure a serial port on a router with the last usable host address in
the 192.216.32.32/29 subnet?
A. Router(config-if)# ip address 192.216.32.38 255.255.255.240
B. Router(config-if)# ip address 192.216.32.39 255.255.255.224
C. Router(config-if)# ip address 192.216.32.63 255.255.255.248
D. Router(config-if)# ip address 192.216.32.39 255.255.255.248
E. Router(config-if)# ip address 192.216.32.63 255.255.255.248
F. Router(config-if)# ip address 192.216.32.38 255.255.255.248
Answer: F

Cisco   640-802   640-802   640-802

NO.21 Data transfer is slow between the source and destination. The quality of service requested by the
transport layer in the OSI reference model is not being maintained. To fix this issue, at which layer should
the troubleshooting process begin?
A. presentation
B. session
C. transport
D. network
E. physical
Answer: D

Cisco   640-802   640-802

NO.22 Which command displays CPU utilization?
A. show protocols
B. show process
C. show system
D. show version
Answer: B

Cisco   640-802 dump   640-802

NO.23 Which command is used to load a configuration from a TFTP server and merge the configuration into
RAM?
A. copy running-config: TFTP:
B. copy TFTP: running-config
C. copy TFTP: startup-config
D. copy startup-config: TFTP:
Answer: B

Cisco자료   640-802 dumps   640-802덤프

NO.24 Refer to the exhibit.
Which WAN protocol is being used?
A. ATM
B. HDLC
C. Frame Relay
D. PPP
Answer: C

Cisco   640-802덤프   640-802   640-802   640-802 pdf

NO.25 The network administrator has asked you to check the status of the workstation's IP stack by pinging the
loopback address. Which address would you ping to perform this task?
A. 10.1.1.1
B. 127.0.0.1
C. 192.168.0.1
D. 239.1.1.1
Answer: B

Cisco   640-802인증   640-802기출문제   640-802

NO.26 Which three options are valid WAN connectivity methods? (Choose three.)
A. PPP
B. WAP
C. HDLC
D. MPLS
E. L2TPv3
F. ATM
Answer: ACF

Cisco dumps   640-802   640-802

NO.27 Which command reveals the last method used to powercycle a router?
A. show reload
B. show boot
C. show running-config
D. show version
Answer: D

Cisco인증   640-802   640-802   640-802기출문제

NO.28 The network default gateway applying to a host by DHCP is 192.168.5.33/28. Which option is the valid
IP address of this host?
A. 192.168.5.55
B. 192.168.5.47
C. 192.168.5.40
D. 192.168.5.32
E. 192.168.5.14
Answer: C

Cisco   640-802 pdf   640-802

NO.29 A system administrator types the command to change the hostname of a router. Where on the Cisco
IFS is that change stored?
A. NVRAM
B. RAM
C. FLASH
D. ROM
E. PCMCIA
Answer: B

Cisco   640-802시험문제   640-802   640-802 dump

NO.30 What is the difference between a CSU/DSU and a modem?
A. A CSU/DSU converts analog signals from a router to a leased line; a modem converts analog signals
from a router to a leased line.
B. A CSU/DSU converts analog signals from a router to a phone line; a modem converts digital signals
from a router to a leased line.
C. A CSU/DSU converts digital signals from a router to a phone line; a modem converts analog signals
from a router to a phone line.
D. A CSU/DSU converts digital signals from a router to a leased line; a modem converts digital signals
from a router to a phone line.
Answer: D

Cisco   640-802   640-802자료   640-802   640-802 pdf

ITExamDump에는 베터랑의전문가들로 이루어진 연구팀이 잇습니다, 그들은 it지식과 풍부한 경험으로 여러 가지 여러분이Cisco인증640-802시험을 패스할 수 있을 자료 등을 만들었습니다, ITExamDump 에서는 일년무료 업뎃을 제공하며, ITExamDump 의 덤프들은 모두 높은 정확도를 자랑합니다. ITExamDump 선택함으로 여러분이Cisco인증640-802시험에 대한 부담은 사라질 것입니다.